Nycote 88 Tinted
Apply Nycote® 88 Tinted to substrates that need protection from corrosion, electrical conduction and friction. It comes in an easy-to-use two-part component. Combining the two components results in a three-hour window before the formula begins to set. Nycote® 88 can be tinted an array of colors in order to assist the identification of parts that have been treated and to improve appearances. Contact factory for custom tinting.
Our products are easily applied by painting, spraying or dipping areas that need protection from aircraft fuels, oil, lubricants, phosphate ester hydraulic fluids, salt spray and water. Nycote® 88 Tinted also provides excellent high impact, abrasion resistance, flexibility and toughness at temperatures of -70°F to +300°F (-57°C to +149°C). NSN: 8010-01-530-5341
Nycote 88 Tinted Application
- Carefully clean surfaces of oils, grease and dust. Nycote® Thinner I followed by Nyclean™ is recommended
- Add accelerator to base container (premeasured ratio of resin to accelerator is 16 to one)
- Close tightly and shake well for two minutes
- Let stand for 10 minutes before use
- Apply Nycote® resin by brush, dip, fill and drain, or spraying techniques
- When spraying we recommend using Nycote® Thinner Type II at a 25% to 50% volume ratio in order to reduce cobwebbing.
Use low air pressure 10-20 p.s.i.
Allow one to two hours air dry to become tack free. In dry air allow 72 hours at room temperature for full cure or:
Heat 12 hours @ 120°F (49°C)
Heat eight hours @ 150°F (66°C)
Heat four hours @ 180°F (82°C)
Heat two hours @ 220°F (105°C)
Cure film temperature range is -70°F to +300°F (-57°C to 149°C)
Storage Temperature Requirements
Store at 70°F (21°C). Keep away from fire or flame.
Note: Ideal storage temperature is 70°F (21°C); acceptable storage range is between 65°F to 80°F (18.3°C to 26.7°C). Storing below 65°F (18.3°C) may cause cloudiness or gel; heat at 180°F (82°C) for two hours. This should restore the product to its normal liquid condition. If possible, re-verify viscosity with Zahn #2 cup (21-27 seconds).
Nycote® 88 Tinted has a 12 month shelf life provided that the accelerator is not added to base product. Once the accelerator has been added, the formula has a three-hour application window before hardening process begins.
Nycote 88 Tinted Specifications
Physical Properties: Temperature Range from -70°F to +300°F (-56°C to 148°C)
|Viscosity: @ 72ºF Zahn #2 Cup||21-27 Seconds||n/a|
|Solids Content (non-vol.)||17%||n/a|
|Flash Point: C.O.C||70°F||n/a|
|Pounds per Gallon @ 78°F||7.4±0.2 lb.||n/a|
|Shelf Life @78°F||12 Months||n/a|
|Film Thickness, 1 Dipcoat||n/a||0.4 mil|
|Coverage Per Gallon||300 sq. ft.||n/a|
|Tack-Free Time, 50% RH @ 70°F||n/a||1 Hour|
|Film Pencil Hardness||n/a||1-H|
|Adhesion (peel test value)||n/a||21 lbs., Per Inch|
|Abrasion Resistance – (500 Gr. #17 wheel 100 cycles)||n/a||2.9 mgm|
Resistance to Fluids: Excellent results in all areas tested
|Fluid Resistance – 30 days immersion @ 75°F|
|100% RH @120°F|
|80% JP-4 Bacteria Laden Distilled Water|
Adhesion Characteristics: Excellent results in all areas tested
|Chem-filmed (Irridited) Aluminum|
|Zinc Chromate Primed Aluminum|
|Any Metal Surface|